#fdm3dprinting — Public Fediverse posts

The lads and lasses of the Averland 22nd “Wild Boars” ready to answer the call.. for the right price.

#warhammertheoldworld #fdm3dprinting #miniaturepainting #WarhammerCommunity

Been working on a Renegade Crowns project. Always had a soft spot for the old Dogs of War (had a small army from 5th edition) so it’s nice to come back to that concept again now.

Here we’ve two galloper guns, a light field gun and an organ gun, with attached crew and carriages.

#warhammertheoldworld #WarhammerCommunity #miniaturepainting #3dprint #fdm3dprinting

Ventarii 27th pike regiment.

Pretty chuffed with how these pike lads have turned out. Very tricky print on the a1 mini, there’s a couple rough spots but by and large I’m damn happy with it all.

#warhammertheoldworld #miniaturepainting #3dprint #fdm3dprinting #WarhammerCommunity

model airplane: FDM printing on tissue paper. Full build in less than 30 minutes. Running on a simple 2.7V/10F SuperCap.

https://www.youtube.com/watch?v=-4X6KYlQ7YQ
#fdm3dprinting #3dprinting

3D hubs no longer exists so I thought it would be nice to have a user-friendly alternative for requesting prints and offering to print for others. Because I seem to be a software engineer I built one myself:

https://3dfabs.org/

Totally free and with all Bambu printers and most Bambu materials preloaded!

#3D #bambuLab #3Dprinting #FDM3dprinting #makers

I was asked to print card holders for Munchkin board game. Most of the models I found were corners, or separators for existing boxes, and I didn't imagine it would be too pleasant to pick a card out, or place it in.
Thankfully, I found a photo of a model of this kind, and since it was unavailable, I reverse-modelled it, with added squirrels and cats.
Used #FreeCAD, #Inkscape, #Cura, and my heavily modified Ender 3v2.
If you by any chance remember my neverending struggle with layer shifts, it finally ended with replacing the board, and installing CrTouch. Whatever was wrong with the board, I'll never know, as it looked and smelled fine, and wasn't overheating at all.
#3dPrinting #fdm3dprinting

On the Benefits of Filling 3D Prints With Spray Foam https://hackaday.com/2025/11/29/on-the-benefits-of-filling-3d-prints-with-spray-foam/ #3dPrinterhacks #FDM3Dprinting #sprayfoam

Does it Make Sense to Upgrade a Prusa Mark 4S to a Core One? https://hackaday.com/2025/08/30/does-it-make-sense-to-upgrade-a-prusa-mark-4s-to-a-core-one/ #3dPrinterhacks #FDM3Dprinting #PrusaCoreONE

Does it Make Sense to Upgrade a Prusa Mark 4S to a Core One? - Some of these Mark 4S parts will become a Prusa Core One. (Credit: Aurora Tech, Yo... - https://hackaday.com/2025/08/30/does-it-make-sense-to-upgrade-a-prusa-mark-4s-to-a-core-one/ #3dprinterhacks #fdm3dprinting #prusacoreone

PVDF: the Specialized Filament for Chemical and Moisture Resistance - There’s a dizzying number of specialist 3D printing materials out there, some of w... - https://hackaday.com/2025/08/28/pvdf-the-specialized-filament-for-chemical-and-moisture-resistance/ #3dprinterfilament #3dprinterhacks #fdm3dprinting

MorPhlex: The TPU Filament That Goes Soft After You Print It - In FDM 3D printing cycles TPU is a bit of a special filament. Not so much because ... - https://hackaday.com/2025/08/16/morphlex-the-tpu-filament-that-goes-soft-after-you-print-it/ #3dprinterhacks #fdm3dprinting #fdm #tpu

MorPhlex: The TPU Filament That Goes Soft After You Print It https://hackaday.com/2025/08/16/morphlex-the-tpu-filament-that-goes-soft-after-you-print-it/ #3dPrinterhacks #FDM3Dprinting #FDM #TPU