#ender3s1pro — Public Fediverse posts
Live and recent posts from across the Fediverse tagged #ender3s1pro, aggregated by home.social.
-
Es baut.
Ich habe jetzt tatsächlich PETG genommen, weil es sowieso geladen war und auch weiß ist. 😂
#3dprinting #hose #elbowjoint #ender3s1pro
/cc @3dprinting
-
Es baut.
Ich habe jetzt tatsächlich PETG genommen, weil es sowieso geladen war und auch weiß ist. 😂
#3dprinting #hose #elbowjoint #ender3s1pro
/cc @3dprinting
-
Ok, now I'm doing this #klipper thing the hard way after all. Installed #MainsailOS on a #RaspberryPi 3B, generated the firmware for the S1 Pro and managed to flash it after 10 attempts. Mounted an S2DW to configure input shaping (had to generate firmware for that too - it has a RasPi 2040 chip onboard), leveled the bed and set up a webcam for time-lapses. Not too bad for one long evening! Now I just need to tweak everything so I can reap the speed benefits of Klipper!
-
Ok, now I'm doing this #klipper thing the hard way after all. Installed #MainsailOS on a #RaspberryPi 3B, generated the firmware for the S1 Pro and managed to flash it after 10 attempts. Mounted an S2DW to configure input shaping (had to generate firmware for that too - it has a RasPi 2040 chip onboard), leveled the bed and set up a webcam for time-lapses. Not too bad for one long evening! Now I just need to tweak everything so I can reap the speed benefits of Klipper!
-
Little bit annoyed with Creality. I thought I'd take the easy route and get the Nebula Kit to upgrade my Ender-3 S1 Pro to Klipper, I even specifically asked their chat support on the official website if those are compatible or if I should get the Sonic Pad instead. Yes, yes, it's all supported. But nope, when you get to the step where you're trying to plug a 1x6 pin plug into a 2x5 pin socket, you realize you've been lied to...
-
Little bit annoyed with Creality. I thought I'd take the easy route and get the Nebula Kit to upgrade my Ender-3 S1 Pro to Klipper, I even specifically asked their chat support on the official website if those are compatible or if I should get the Sonic Pad instead. Yes, yes, it's all supported. But nope, when you get to the step where you're trying to plug a 1x6 pin plug into a 2x5 pin socket, you realize you've been lied to...
-
With and without input shaping on my 3D printer. It makes a massive difference in being able to print at high speed. Cut my draft prints from like 6 hours to 2 hours.
Installing Klipper was pretty easy, the calibration took a bit of time but it was worth it. -
With and without input shaping on my 3D printer. It makes a massive difference in being able to print at high speed. Cut my draft prints from like 6 hours to 2 hours.
Installing Klipper was pretty easy, the calibration took a bit of time but it was worth it. -
Hier ist mein komplett umgebauter Druckkopf. Zwei neue Lüfter und Touch Sensor nun auf Höhe der Nozzle (y-offset = 0).
Alles viel leiser und mehr Luft am Bauteil.
-
Hier ist mein komplett umgebauter Druckkopf. Zwei neue Lüfter und Touch Sensor nun auf Höhe der Nozzle (y-offset = 0).
Alles viel leiser und mehr Luft am Bauteil.
-
Musste er schon echt kämpfen, mein Ender. Am Bug gab es die größten Schwierigkeiten.
700% mit Klipper, 33min (Standard 1h 28min)
-
Musste er schon echt kämpfen, mein Ender. Am Bug gab es die größten Schwierigkeiten.
700% mit Klipper, 33min (Standard 1h 28min)
-
Seufz, habe jetzt das High Flow Hotend bestellt.
Bin gespannt, ob das was wirklich bringt.
-
Seufz, habe jetzt das High Flow Hotend bestellt.
Bin gespannt, ob das was wirklich bringt.
-
I published my Top-plate Extension for Accante #Creality #Ender 3 S1 (pro) Housing on #Printables.
https://www.printables.com/de/model/640233-top-plate-extension-for-accante-creality-ender-3-s
-
I published my Top-plate Extension for Accante #Creality #Ender 3 S1 (pro) Housing on #Printables.
https://www.printables.com/de/model/640233-top-plate-extension-for-accante-creality-ender-3-s
-
Ok, it fits.
Top plates for Accante housing for Creality #ender3s1pro. Additionaly, an extender arm for the spool holder.
-
Ok, it fits.
Top plates for Accante housing for Creality #ender3s1pro. Additionaly, an extender arm for the spool holder.
-
-
-
Ich werde übrigens PLA+ erstmal verwenden. PETG wird vermutlich nicht notwendig sein. Im Zweifel tausche ich es mal aus. ABS kann ich erst drucken, wenn das Gehäuse fertig ist. Das dann evtl. nochmal für die Scharniere.
Mal sehen.
Ich bin eigentlich sehr zufrieden mit der Festigkeit des PLA+ von eSun.
-
Ich werde übrigens PLA+ erstmal verwenden. PETG wird vermutlich nicht notwendig sein. Im Zweifel tausche ich es mal aus. ABS kann ich erst drucken, wenn das Gehäuse fertig ist. Das dann evtl. nochmal für die Scharniere.
Mal sehen.
Ich bin eigentlich sehr zufrieden mit der Festigkeit des PLA+ von eSun.
-
First serious modification to our 3d printer. Replaced the stock hot end fan with two 5015's and a 3d printed duct in red PETG. The red makes it go faster. The new fans + duct should allow for some insane unsupported overhangs. #3dprinting #Ender3S1Pro
-
First serious modification to our 3d printer. Replaced the stock hot end fan with two 5015's and a 3d printed duct in red PETG. The red makes it go faster. The new fans + duct should allow for some insane unsupported overhangs. #3dprinting #Ender3S1Pro
-
My 14 yr old designed this lightsaber hilt in Onshape and then printed it on our Ender3. I'm so impressed. #3dprinting #Ender3S1Pro #BananaForScale
-
My 14 yr old designed this lightsaber hilt in Onshape and then printed it on our Ender3. I'm so impressed. #3dprinting #Ender3S1Pro #BananaForScale
-
@elijahmanor @anthonyfloyd got a #Ender3S1Pro last month and has written in great detail about setup & tuning adventures - might be something there that will save you some time: https://www.anthonyfloyd.ca/category/3d-printing/
-
@elijahmanor @anthonyfloyd got a #Ender3S1Pro last month and has written in great detail about setup & tuning adventures - might be something there that will save you some time: https://www.anthonyfloyd.ca/category/3d-printing/
-
And here's the top part, after 38 hrs printing! #3dprinting #ender3s1pro
-
And here's the top part, after 38 hrs printing! #3dprinting #ender3s1pro
-
32 hrs into this print. 6.5 more to go? #3dprinting #Ender3S1Pro
-
Bottom half of my kid's new mug, printing. Looks nice but we're 10.5 hrs in! #3dprinting #Ender3S1Pro
-
Bottom half of my kid's new mug, printing. Looks nice but we're 10.5 hrs in! #3dprinting #Ender3S1Pro
-
Blog post: 3D Printing, Day 3. It got better. https://www.anthonyfloyd.ca/2022/12/29/3d-printing-day-3/ #3dprinting #Ender3S1Pro
-
Day 2, Electric Boogaloo. Auto-levelling problems galore.
https://www.anthonyfloyd.ca/2022/12/27/ender-3-s1-pro-day-2/
-
Day 2, Electric Boogaloo. Auto-levelling problems galore.
https://www.anthonyfloyd.ca/2022/12/27/ender-3-s1-pro-day-2/
-
Been offline for the past little bit, in no small part because we got a 3D printer for Christmas. Printing all the things now! #3DPrinting #benchy #Ender3S1Pro
-
Been offline for the past little bit, in no small part because we got a 3D printer for Christmas. Printing all the things now! #3DPrinting #benchy #Ender3S1Pro