#makerhelp — Public Fediverse posts
Live and recent posts from across the Fediverse tagged #makerhelp, aggregated by home.social.
-
Anyone UK got a good source for #lasercutter 'ble 5mm thick EVA foam? Been using a random sheet I had but could do with a stock of it. #makerhelp
-
Anyone UK got a good source for #lasercutter 'ble 5mm thick EVA foam? Been using a random sheet I had but could do with a stock of it. #makerhelp
-
Anyone UK got a good source for #lasercutter 'ble 5mm thick EVA foam? Been using a random sheet I had but could do with a stock of it. #makerhelp
-
Anyone UK got a good source for #lasercutter 'ble 5mm thick EVA foam? Been using a random sheet I had but could do with a stock of it. #makerhelp
-
Anyone UK got a good source for #lasercutter 'ble 5mm thick EVA foam? Been using a random sheet I had but could do with a stock of it. #makerhelp
-
If you work with laser cut veneer covered plywood, which kind of finish do you apply to it that looks good and offers decent protection? And, ideally, highlighting any laser etching too. Varnish? Beeswax? Shellac?
-
If you work with laser cut veneer covered plywood, which kind of finish do you apply to it that looks good and offers decent protection? And, ideally, highlighting any laser etching too. Varnish? Beeswax? Shellac?
-
If you work with laser cut veneer covered plywood, which kind of finish do you apply to it that looks good and offers decent protection? And, ideally, highlighting any laser etching too. Varnish? Beeswax? Shellac?
-
If you work with laser cut veneer covered plywood, which kind of finish do you apply to it that looks good and offers decent protection? And, ideally, highlighting any laser etching too. Varnish? Beeswax? Shellac?
-
If you work with laser cut veneer covered plywood, which kind of finish do you apply to it that looks good and offers decent protection? And, ideally, highlighting any laser etching too. Varnish? Beeswax? Shellac?
-
So Mastodon electronics/repair shops/etc people - what is the best way to restore those rubber/graphite keyboard pads you get on many music keyboards?
I'm getting a very intermittent signal when the keyboard is scanning on some keys...
-
So Mastodon electronics/repair shops/etc people - what is the best way to restore those rubber/graphite keyboard pads you get on many music keyboards?
I'm getting a very intermittent signal when the keyboard is scanning on some keys...
-
So Mastodon electronics/repair shops/etc people - what is the best way to restore those rubber/graphite keyboard pads you get on many music keyboards?
I'm getting a very intermittent signal when the keyboard is scanning on some keys...
-
So Mastodon electronics/repair shops/etc people - what is the best way to restore those rubber/graphite keyboard pads you get on many music keyboards?
I'm getting a very intermittent signal when the keyboard is scanning on some keys...
-
So Mastodon electronics/repair shops/etc people - what is the best way to restore those rubber/graphite keyboard pads you get on many music keyboards?
I'm getting a very intermittent signal when the keyboard is scanning on some keys...
-
Anyone know enough about the ATmega328 to know if the UART can cope with something else disabling interrupts for ~2mS...?
That sounds like quite a lot to me.
This is for handling MIDI, so I think at 31250 that would be enough for up to two complete 3-byte messages to have gone past...
Am about to pile into the datasheet, but the UART was always a bit of "mystery magic that just worked" for me...
-
Anyone know enough about the ATmega328 to know if the UART can cope with something else disabling interrupts for ~2mS...?
That sounds like quite a lot to me.
This is for handling MIDI, so I think at 31250 that would be enough for up to two complete 3-byte messages to have gone past...
Am about to pile into the datasheet, but the UART was always a bit of "mystery magic that just worked" for me...
-
Anyone know enough about the ATmega328 to know if the UART can cope with something else disabling interrupts for ~2mS...?
That sounds like quite a lot to me.
This is for handling MIDI, so I think at 31250 that would be enough for up to two complete 3-byte messages to have gone past...
Am about to pile into the datasheet, but the UART was always a bit of "mystery magic that just worked" for me...
-
Anyone know enough about the ATmega328 to know if the UART can cope with something else disabling interrupts for ~2mS...?
That sounds like quite a lot to me.
This is for handling MIDI, so I think at 31250 that would be enough for up to two complete 3-byte messages to have gone past...
Am about to pile into the datasheet, but the UART was always a bit of "mystery magic that just worked" for me...
-
Anyone know enough about the ATmega328 to know if the UART can cope with something else disabling interrupts for ~2mS...?
That sounds like quite a lot to me.
This is for handling MIDI, so I think at 31250 that would be enough for up to two complete 3-byte messages to have gone past...
Am about to pile into the datasheet, but the UART was always a bit of "mystery magic that just worked" for me...
-
Anyone know anything about the Boss GT-1000 pedal/thing?
Someone is having issues with its MIDI being recogised by MiniDexed and I could really do with knowing what USB endpoints it has :)
There are bespoke drivers for Windows, but I can't find a definitive comment about support in Linux...
-
Anyone know anything about the Boss GT-1000 pedal/thing?
Someone is having issues with its MIDI being recogised by MiniDexed and I could really do with knowing what USB endpoints it has :)
There are bespoke drivers for Windows, but I can't find a definitive comment about support in Linux...
-
Anyone know anything about the Boss GT-1000 pedal/thing?
Someone is having issues with its MIDI being recogised by MiniDexed and I could really do with knowing what USB endpoints it has :)
There are bespoke drivers for Windows, but I can't find a definitive comment about support in Linux...
-
Anyone know anything about the Boss GT-1000 pedal/thing?
Someone is having issues with its MIDI being recogised by MiniDexed and I could really do with knowing what USB endpoints it has :)
There are bespoke drivers for Windows, but I can't find a definitive comment about support in Linux...
-
Anyone know anything about the Boss GT-1000 pedal/thing?
Someone is having issues with its MIDI being recogised by MiniDexed and I could really do with knowing what USB endpoints it has :)
There are bespoke drivers for Windows, but I can't find a definitive comment about support in Linux...
-
Anyone know a good source (UK) for inexpensive ESD/anti static foam for IC storage?
-
Anyone know a good source (UK) for inexpensive ESD/anti static foam for IC storage?
-
Anyone know a good source (UK) for inexpensive ESD/anti static foam for IC storage?
-
Anyone know a good source (UK) for inexpensive ESD/anti static foam for IC storage?
-
Anyone know a good source (UK) for inexpensive ESD/anti static foam for IC storage?