#km84clonebuild — Public Fediverse posts

And then there were two.

#KM84CloneBuild

Got KM84 clone number 2 done a few moments ago. The learning curve from having done the first one helped immensely with getting this one finished quickly. Biasing the FET was much quicker this time too since I learned a way to limit the 60 Hz hum while viewing the 1K sine wave on the scope.

Onto a large diaphragm version of this next. Someone took this circuit and modded it for large diaphragm mic capsules and made a PCB that fits perfectly into an inexpensive mic body.

#KM84CloneBuild

I'll get KM84 clone #2 basically finished tomorrow, as well. Then at some point I need to repaint the main bodies. I filled the MXL logos with bondo, so a re-spray is in order (see attached photo).

These were quite the adventure. Because of the cheap nature of the MXL bodies I had to drill out stripped set-screws, and retap for slightly bigger ones. I had to relocate some holes because of that as well. But at the end of the day these are going to be pretty cool.

#KM84CloneBuild

OK, I set aside this weekend for "finishing" the KM84 clones. I've had all the stuff to finish them for a couple weeks, but last weekend I wasn't feeling well.

Got the transformer soldered, wired the XLR, and soldered the capsule contact lead to the PCB, applied phantom power, and voila... NO SMOKE. It even made a sound when you tapped on it. Got the FET biased properly and it sounds super cool.

I had a small issue after my initial bias attempt but I got past it.

Here it is.

#KM84CloneBuild

I intended to go into the lab and do some soldering today to get one of the KM84s "working," but nerve pain had its own ideas. No real rush but I would rather have been doing that.

I'll try to do some bits and pieces during the week, and then next weekend also.

#KM84CloneBuild

OK, coolio. The transformers have arriven. Seen here in this glamour pic are the transformers used in my KM84 clones. These transformers are high quality clones of the original Neumann BV107, but since these are still being made, you can actually buy them, and for a reasonable price. Maybe I'll have working mics by the weekend. But then again, it IS new years weekend, so maybe there will be less building and more partying.

#KM84CloneBuild

@wigwam

Ooh! Super excited. Just got confirmation that the transformers for the KM84 clone build were delivered. Woot!

Pictures later.

#KM84CloneBuild

OK, the transformers for my KM84 clones have shipped. Can't wait to bias these bad boys up and hear how they sound.

#KM84CloneBuild

Ok, I think I have the embossed MXL logos filled and sanded to the point where you won't see them with a code of primer and paint on it. So I think I'm ready to shoot these with some primer.

#KM84CloneBuild

I bought a rubber metal-forming block to shape these badges that need to go on the curved mic bodies on the left. So I found a socket of similar size put a extension on it for a handle, turned the little logo badge upside down and oriented it correctly, put the socket over it and then struck it hard with a big mallet. And I got a fairly perfectly curved emblem that will fit over the mic body nicely. This is for the Neumann KM84 mic clones that I am building.

#KM84CloneBuild

I applied some of this fancy schmancy metalized Bondo to the old MXL logo to fill in the embossed letters on these SDC mic bodies. I'll do a few coats and then do a light sanding and see where we are.

#KM84CloneBuild

I bought a rubber metal-forming block to shape these badges that need to go on the curved mic bodies on the left. So I found a socket of similar size put a extension on it for a handle, turned the little logo badge upside down and oriented it correctly, put the socket over it and then struck it hard with a big mallet. And I got a fairly perfectly curved emblem that will fit over the mic body nicely.

#KM84CloneBuild

Just as an FYI this is the filler I'll be using to fill in the logo on those mic bodies. This stuff is supposed to be the bomb-skiddley-shiznit.

https://www.3m.com/3M/en_US/p/d/b40067480/

#KM84CloneBuild

So when I was using nail polish remover to remove the black silk screening or whatever it was in the embossed MXL logo, the silver finish came off also.

So after I fill and sand the MXL logo smooth, I'll need to repaint them.

Rattle cans put paint on too thick, don't they? Or is there a thinner one that's more like the consistency of airbrushing?

What airbrush paint would anyone recommend that can stand up to being handled?

#KM84CloneBuild

Drilled a bunch of holes today that needed to be tapped for #3 set screws. Yep. SMALL holes. It all went pretty well, but the real issue was I didn't have any sort of jig to hold the piece I was drilling, which was a weird shape. So 5 holes came out great and the tap worked well, but one of the holes moved while I was drilling it, and the hole ended up being a bit too big and didn't tap tight enough to hold the tiny set screws.

That said, all in all I'd call it a win.

#KM84CloneBuild

Gotta drill those precision holes on the weekend and tap them for the #3 set screws I'll be using in the #KM84CloneBuild . Not looking forward to it since I don't have the drill press I need to do the job properly, but hopefully I'll figure it out.

#KM84CloneBuild

Excellent. My mic capsules for the #KM84CloneBuild have shipped from China. Can't wait to hear these.

#KM84CloneBuild

OK, capsules ordered for the #KM84CloneBuild .

Then I need to get the transformers, and we'll be ready to record with them!

#KM84CloneBuild

@havoc

#D87Build
#TubePreBuild
#PMillettBuild
#ActiveDIBuild
#CAPI500Build
#CP5Build
#SSL4000GBuild
#SSL9kBuild
#1176Build
#LoudLifterBuild
#TubeHiFiPreampBuild
#ClassDAmpBuild
#RibbonMicBuild
#SSLBusComp
#CAPIVP25Build
#ML12Build
#MP573Build
#Neve1073Build
#LevelLocBuild
#RatPedalBuild
#Mackie1202Upgrade
#BalancedOutputBox
#LowFiMicBuild
#CarbonMicBuild
#500SeriesAPIClone
#KM84CloneBuild
#FET847MicBuild

Man, I got so many projects on the backburner I am forgetting about them.

The FET847 build takes the KM84 SDC circuit (which I am building now in the #KM84CloneBuild ) and modified it to work with Large Diaphragm Condensers. He designed the PCBs to fit into an inexpensive Chinese mic body.

I got to get on these and add them to the mic locker!

#FET847MicBuild

OK, I will be ordering the transformers and cardioid capsules for the #KM84CloneBuild.

Should be able to get them with the next pay check. I need to build up the 2nd board, and do some metal fabrication, but once I get the transformers I can bias the FETs and they'll be really close to done.

#KM84CloneBuild

Working on my #KM84CloneBuild today. Soldered up one of the boards. I'll do the other board next week. Then I have to order the transformers (pricey!) and do some metal work, and then I have to order better quality capsules, which if they're not available yet, should be soon.

For those interested, this board is designed to fit into an MXL603, which you buy just to get the bodies. You use this classic Neumann circuit and get some better capsules and you really have something.

#KM84CloneBuild

Upcoming projects include a pair of Neumann KM84 clones, and some more API clones in 500 series.

#KM84CloneBuild
#APIPreampCloneBuild