#bitx-17a — Public Fediverse posts

BitX 17a – IF Filter #2

Following up on BitX 17a – IF Filter, @n8dmt suggested that I could use a nanoVNA for this as well. After some fiddling with settings, I got it to work! The results are slightly different than what I measured before.

#bitx17a #filter #hamRadio #kit

BitX 17a – IF Filter #2

Following up on BitX 17a – IF Filter, @n8dmt suggested that I could use a nanoVNA for this as well. After some fiddling with settings, I got it to work! The results are slightly different than what I measured before.

#bitx17a #filter #hamRadio #kit

BitX 17a – IF Filter #2

Following up on BitX 17a – IF Filter, @n8dmt suggested that I could use a nanoVNA for this as well. After some fiddling with settings, I got it to work! The results are slightly different than what I measured before.

#bitx17a #filter #hamRadio #kit

BitX 17a – IF Filter #2

Following up on BitX 17a – IF Filter, @n8dmt suggested that I could use a nanoVNA for this as well. After some fiddling with settings, I got it to work! The results are slightly different than what I measured before.

#bitx17a #filter #hamRadio #kit

BitX 17a – IF Filter #2

Following up on BitX 17a – IF Filter, @n8dmt suggested that I could use a nanoVNA for this as well. After some fiddling with settings, I got it to work! The results are slightly different than what I measured before.

#bitx17a #filter #hamRadio #kit

BitX 17a – IF Filter

I was graciously given a partially completed BitX 17a kit by Thaire W2APF back in June, and I’ve been working on it slowly. The tests seem to be working out OK, and I’ve even gotten to use the oscilloscope and the tinySA a few times.

Here are a few notes on the IF filter measurement based on what I understand from the manual.

At this point you have the first opportunity to see the IF Filter passband. If you slowly tune the 12.96 MHz signal across the IF frequency range while monitoring RF voltage at the ungrounded end of R65 with an oscilloscope or an RF detection probe and voltmeter you can see the relative response at various frequencies. By recording the signal level at 200 Hz intervals and plotting this on graph paper you can generate a picture of the IF filter response curve. Unless you convert your voltage readings to log scale though they will look a bit rough. For a truly representative graph you need to convert your voltage readings to db.
It is possible to set the BFO frequency now. Once you know where the lower edge of the IF filter passband is located, you can calculate the 20 db point on that slope and set your BFO for that frequency. Alternatively, you can adjust the BFO so you can hear the zerobeat as you tune across the upper sideband but not hear it on the lower sideband. That will get you in the right area for later fine tuning on a signal being received from the antenna.

Input -18.5 dBm. Low output ON for signal. Mod None. Adjust frequency on tinySA by hand.
Measure VRMS on scope.

Frequency, HzVRMS, mVVRMS, dBm12,962,00028-18.0512,961,80030-17.4512,961,60030-17.4512,961,40035-16.1112,961,20050-13.0112,961,00090-7.9012,960,800160-2.9112,960,6004205.4812,960,4004405.8812,960,2003824.6512,960,0004155.3712,959,8004706.4512,959,6004806.6412,959,4004706.4512,959,2004706.4512,959,0004506.0712,958,8004506.0712,958,6004706.4512,958,4004706.4512,958,2004706.4512,958,0004706.4512,957,8004806.6412,957,6004355.7812,957,4002250.0512,957,200138-4.1912,957,00075-9.4912,956,80055-12.1812,956,60040-14.9512,956,40035-16.1112,956,20030-17.4512,956,00030-17.45Plot of output signal (y-axis, dBm) as a function of input frequency (x-axis, Hz).

Lower edge of the passband appears to be at 12,957,600 Hz, which is 5.78 dBm. 20 dBm down from that is -14.22, which is at about 12,956,700 Hz. Let’s aim the BFO for that I guess.

Did I do this wrong? Please let me know!

#bitx17a #hamRadio #kit #ssb

BitX 17a – IF Filter

I was graciously given a partially completed BitX 17a kit by Thaire W2APF back in June, and I’ve been working on it slowly. The tests seem to be working out OK, and I’ve even gotten to use the oscilloscope and the tinySA a few times.

Here are a few notes on the IF filter measurement based on what I understand from the manual.

At this point you have the first opportunity to see the IF Filter passband. If you slowly tune the 12.96 MHz signal across the IF frequency range while monitoring RF voltage at the ungrounded end of R65 with an oscilloscope or an RF detection probe and voltmeter you can see the relative response at various frequencies. By recording the signal level at 200 Hz intervals and plotting this on graph paper you can generate a picture of the IF filter response curve. Unless you convert your voltage readings to log scale though they will look a bit rough. For a truly representative graph you need to convert your voltage readings to db.
It is possible to set the BFO frequency now. Once you know where the lower edge of the IF filter passband is located, you can calculate the 20 db point on that slope and set your BFO for that frequency. Alternatively, you can adjust the BFO so you can hear the zerobeat as you tune across the upper sideband but not hear it on the lower sideband. That will get you in the right area for later fine tuning on a signal being received from the antenna.

Input -18.5 dBm. Low output ON for signal. Mod None. Adjust frequency on tinySA by hand.
Measure VRMS on scope.

Frequency, HzVRMS, mVVRMS, dBm12,962,00028-18.0512,961,80030-17.4512,961,60030-17.4512,961,40035-16.1112,961,20050-13.0112,961,00090-7.9012,960,800160-2.9112,960,6004205.4812,960,4004405.8812,960,2003824.6512,960,0004155.3712,959,8004706.4512,959,6004806.6412,959,4004706.4512,959,2004706.4512,959,0004506.0712,958,8004506.0712,958,6004706.4512,958,4004706.4512,958,2004706.4512,958,0004706.4512,957,8004806.6412,957,6004355.7812,957,4002250.0512,957,200138-4.1912,957,00075-9.4912,956,80055-12.1812,956,60040-14.9512,956,40035-16.1112,956,20030-17.4512,956,00030-17.45Plot of output signal (y-axis, dBm) as a function of input frequency (x-axis, Hz).

Lower edge of the passband appears to be at 12,957,600 Hz, which is 5.78 dBm. 20 dBm down from that is -14.22, which is at about 12,956,700 Hz. Let’s aim the BFO for that I guess.

Did I do this wrong? Please let me know!

#bitx17a #hamRadio #kit #ssb

BitX 17a – IF Filter

I was graciously given a partially completed BitX 17a kit by Thaire W2APF back in June, and I’ve been working on it slowly. The tests seem to be working out OK, and I’ve even gotten to use the oscilloscope and the tinySA a few times.

Here are a few notes on the IF filter measurement based on what I understand from the manual.

At this point you have the first opportunity to see the IF Filter passband. If you slowly tune the 12.96 MHz signal across the IF frequency range while monitoring RF voltage at the ungrounded end of R65 with an oscilloscope or an RF detection probe and voltmeter you can see the relative response at various frequencies. By recording the signal level at 200 Hz intervals and plotting this on graph paper you can generate a picture of the IF filter response curve. Unless you convert your voltage readings to log scale though they will look a bit rough. For a truly representative graph you need to convert your voltage readings to db.
It is possible to set the BFO frequency now. Once you know where the lower edge of the IF filter passband is located, you can calculate the 20 db point on that slope and set your BFO for that frequency. Alternatively, you can adjust the BFO so you can hear the zerobeat as you tune across the upper sideband but not hear it on the lower sideband. That will get you in the right area for later fine tuning on a signal being received from the antenna.

Input -18.5 dBm. Low output ON for signal. Mod None. Adjust frequency on tinySA by hand.
Measure VRMS on scope.

Frequency, HzVRMS, mVVRMS, dBm12,962,00028-18.0512,961,80030-17.4512,961,60030-17.4512,961,40035-16.1112,961,20050-13.0112,961,00090-7.9012,960,800160-2.9112,960,6004205.4812,960,4004405.8812,960,2003824.6512,960,0004155.3712,959,8004706.4512,959,6004806.6412,959,4004706.4512,959,2004706.4512,959,0004506.0712,958,8004506.0712,958,6004706.4512,958,4004706.4512,958,2004706.4512,958,0004706.4512,957,8004806.6412,957,6004355.7812,957,4002250.0512,957,200138-4.1912,957,00075-9.4912,956,80055-12.1812,956,60040-14.9512,956,40035-16.1112,956,20030-17.4512,956,00030-17.45Plot of output signal (y-axis, dBm) as a function of input frequency (x-axis, Hz).

Lower edge of the passband appears to be at 12,957,600 Hz, which is 5.78 dBm. 20 dBm down from that is -14.22, which is at about 12,956,700 Hz. Let’s aim the BFO for that I guess.

Did I do this wrong? Please let me know!

#bitx17a #hamRadio #kit #ssb

BitX 17a – IF Filter

I was graciously given a partially completed BitX 17a kit by Thaire W2APF back in June, and I’ve been working on it slowly. The tests seem to be working out OK, and I’ve even gotten to use the oscilloscope and the tinySA a few times.

Here are a few notes on the IF filter measurement based on what I understand from the manual.

At this point you have the first opportunity to see the IF Filter passband. If you slowly tune the 12.96 MHz signal across the IF frequency range while monitoring RF voltage at the ungrounded end of R65 with an oscilloscope or an RF detection probe and voltmeter you can see the relative response at various frequencies. By recording the signal level at 200 Hz intervals and plotting this on graph paper you can generate a picture of the IF filter response curve. Unless you convert your voltage readings to log scale though they will look a bit rough. For a truly representative graph you need to convert your voltage readings to db.
It is possible to set the BFO frequency now. Once you know where the lower edge of the IF filter passband is located, you can calculate the 20 db point on that slope and set your BFO for that frequency. Alternatively, you can adjust the BFO so you can hear the zerobeat as you tune across the upper sideband but not hear it on the lower sideband. That will get you in the right area for later fine tuning on a signal being received from the antenna.

Input -18.5 dBm. Low output ON for signal. Mod None. Adjust frequency on tinySA by hand.
Measure VRMS on scope.

Frequency, HzVRMS, mVVRMS, dBm12,962,00028-18.0512,961,80030-17.4512,961,60030-17.4512,961,40035-16.1112,961,20050-13.0112,961,00090-7.9012,960,800160-2.9112,960,6004205.4812,960,4004405.8812,960,2003824.6512,960,0004155.3712,959,8004706.4512,959,6004806.6412,959,4004706.4512,959,2004706.4512,959,0004506.0712,958,8004506.0712,958,6004706.4512,958,4004706.4512,958,2004706.4512,958,0004706.4512,957,8004806.6412,957,6004355.7812,957,4002250.0512,957,200138-4.1912,957,00075-9.4912,956,80055-12.1812,956,60040-14.9512,956,40035-16.1112,956,20030-17.4512,956,00030-17.45Plot of output signal (y-axis, dBm) as a function of input frequency (x-axis, Hz).

Lower edge of the passband appears to be at 12,957,600 Hz, which is 5.78 dBm. 20 dBm down from that is -14.22, which is at about 12,956,700 Hz. Let’s aim the BFO for that I guess.

Did I do this wrong? Please let me know!

#bitx17a #hamRadio #kit #ssb

BitX 17a – IF Filter

I was graciously given a partially completed BitX 17a kit by Thaire W2APF back in June, and I’ve been working on it slowly. The tests seem to be working out OK, and I’ve even gotten to use the oscilloscope and the tinySA a few times.

Here are a few notes on the IF filter measurement based on what I understand from the manual.

At this point you have the first opportunity to see the IF Filter passband. If you slowly tune the 12.96 MHz signal across the IF frequency range while monitoring RF voltage at the ungrounded end of R65 with an oscilloscope or an RF detection probe and voltmeter you can see the relative response at various frequencies. By recording the signal level at 200 Hz intervals and plotting this on graph paper you can generate a picture of the IF filter response curve. Unless you convert your voltage readings to log scale though they will look a bit rough. For a truly representative graph you need to convert your voltage readings to db.
It is possible to set the BFO frequency now. Once you know where the lower edge of the IF filter passband is located, you can calculate the 20 db point on that slope and set your BFO for that frequency. Alternatively, you can adjust the BFO so you can hear the zerobeat as you tune across the upper sideband but not hear it on the lower sideband. That will get you in the right area for later fine tuning on a signal being received from the antenna.

Input -18.5 dBm. Low output ON for signal. Mod None. Adjust frequency on tinySA by hand.
Measure VRMS on scope.

Frequency, HzVRMS, mVVRMS, dBm12,962,00028-18.0512,961,80030-17.4512,961,60030-17.4512,961,40035-16.1112,961,20050-13.0112,961,00090-7.9012,960,800160-2.9112,960,6004205.4812,960,4004405.8812,960,2003824.6512,960,0004155.3712,959,8004706.4512,959,6004806.6412,959,4004706.4512,959,2004706.4512,959,0004506.0712,958,8004506.0712,958,6004706.4512,958,4004706.4512,958,2004706.4512,958,0004706.4512,957,8004806.6412,957,6004355.7812,957,4002250.0512,957,200138-4.1912,957,00075-9.4912,956,80055-12.1812,956,60040-14.9512,956,40035-16.1112,956,20030-17.4512,956,00030-17.45Plot of output signal (y-axis, dBm) as a function of input frequency (x-axis, Hz).

Lower edge of the passband appears to be at 12,957,600 Hz, which is 5.78 dBm. 20 dBm down from that is -14.22, which is at about 12,956,700 Hz. Let’s aim the BFO for that I guess.

Did I do this wrong? Please let me know!

#bitx17a #hamRadio #kit #ssb